INSTRUCTIONS: Construction Of A Microcontroller Based T-Junction Traffic Light Controller project material. Please, sit back and study the below research material carefully. DO NOT copy word for word. CareersHelp aim of providing Construction Of A Microcontroller Based T-Junction Traffic Light Controller project research material is to reduce the stress of moving from one school library to another all in the name of searching for Construction Of A Microcontroller Based T-Junction Traffic Light Controller research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works. According to Austin Kleon "All creative work builds on what came before"
You are reading project material titled: Construction Of A Microcontroller Based T-Junction Traffic Light Controller
Table of Contents
List of Figures
1.1 Background of the Study
1.2 Objective of the Project
1.3 Scope of the Study
1.4 Project Report Organization
2.0 LITERATURE REVIEW
2.2 Pre-Emption And Priority
2.3 Special Provisions
2.5 Control And Co-Ordination
2.6 Design Layout And Operation Site
3.0 DESCRIPTION OF SYSTEMS
3.1 The Power Supply
3.2 The Voltage Regulator
3.3 Crystal Oscillator
3.4 Paper Capacitor
3.5 The Microcontroller
3.6 System Flow Diagram
3.7 Light Indicator Stage
3.10 Bridge Rectifier
3.11 Electrolytic Capacitor
3.12 Step Down Transformer
3.13 Seven Segment Display
4.0 SYSTEMS OPERATIONAL UNITS
4.1 The Control Unit
4.2 System Analysis
4.3 Choice Of Counter
4.4 The Interface Unit
4.5 Test And Result
4.8 Bill Of Engineering Measurement And Evaluation
5.0 CONCLUSION AND RECOMMENDATIONS
5.3 Suggestions For Further Research
1.1 BACKGROUND OF THE STUDY
The traffic on our roads, especially intra-city traffic due to increasing number of cars grow by the day and unless adequate steps are taken to control the situation, we shall soon meet with circumstances we do not bargain for. That the innumerable traffic junctions in the country by far out-number the staff strength of the traffic wardens available and that the traffic wardens even where they are enough to control all the junctions cannot do so throughout the day is not in doubt. Traffic control at T.junctions or elsewhere ensures orderliness of movements of vehicles, goods and pedestrians while its absence strongly indicates chaos and most at times leads to accidents.
In the light of the above, it is imperative to recognize the need to compliment the physical exhausting efforts of the traffic wardens. In doing so, steps to be taken should assume permanence in nature rather than any ad-hoc exercise. Such is the role expected to be played by an installed operational road junction traffic controller.
This project –DESIGN AND CONSTRUCTION OF A THREE WAY JUNCTION TRAFFIC LIGHT CONTROLLER is such a device that will play significant role in controlling traffic at junctions to ease the expected increased rush at such junctions and reduce to minimum such disorderliness that may arise as well as allowing the
pedestrians a right of the way at intervals rather than being struck down when in a hurry to cross the roads.
Such an electrical system with a touch of electronics that controls the flow of traffic in a pre-determine sequential pattern at a junction has its diagram below with blocks representing distinct units.
Fig 1.1: Traffic Light Control System
The power supply unit provides the control unit with specified dc voltage from primary source, which is a 240v, 50Hz ac supply, from public power system. The pulse generator containing a timer generates pulse for the system. The clock or counter moderates the signal that enters the decoding logic system.
The display unit of each stand consists of three bulbs Red in colour showing STOP, three bulbs Amber in colour showing GET READY and three bulbs Green in colour showing MOVE.
1.2 OBJECTIVE OF THE PROJECT
Dc Power Supply
The main objective of the study includes:
5 To investigate the practicality of the theoretical knowledge about these components to be used.
6 To experiment on the compatibility of the working relation between components to be used.
7 To investigate the extent to which the design and construction of the control unit can be useful to mankind.
8 To investigate the immediate usefulness of the control system as complimentary to traffic wardens.
1.3 SCOPE OF THE STUDY
The scope of this project is to enlighten all electronics students on the use of microcontroller base traffic light (3-ways) and timer system in T-junction. On the practical usage it is limited to the laboratory used for reference purpose. The larger application of this project work is found in most of our mega cities like Abuja, Lagos, Calabar, Enugu etc, to control and manage heavy traffic congestion.
1.4 PROJECT REPORT ORGANIZATION
This report is structured to follow the history and origin of traffic light system all through the design and implementation phase. The report takes into account the step-by-step process followed in order to arrive at the final design.
Chapter one of this report introduces the concept of the Traffic light system and its objectives. Chapter two centers on the literature review, the origin and history of Traffic light systems and its basic functionality. Chapter Three explains the components which make up the Traffic light system and their basic functionalities/mode of operation. Chapter Four discusses the design procedure, construction, steps and packaging.
Chapter five handles the tests and results as well as conclusion and recommendation.